Sand Calculator

Estimate sand for a sandbox, bedding layer or landscape project in yards, tons and bags.

Your measurements

Order options

Your estimate

Live calculation
1.23yd³

Measured quantity · no extra allowance

Order volume33.33 ft³
Estimated weight1.67 US tons
Whole bags67 0.5 ft³

Calculation & all units

200 ft² × 2 in ÷ 324 × 1 = 1.23 yd³

Order volume
33.3333 ft³
Estimated weight
1.6667 US tons
Whole bags
67 0.5 ft³
Area
200 ft²
Measured volume
1.2346 yd³
Metric volume
0.9439 m³
Metric mass
1,511.9746 kg
Volume-based truckloads
1 loads
Measurement planDimensions in feet
A dimension guide for your estimate
Estimate1.23 yd³View result

Calculation method

Use the actual inside dimensions of a sandbox and the intended fill height. Dry and wet sand have different weights for the same volume. Choose a representative density or enter the supplier’s figure.

Volume in yd³ = length × width × depth in inches ÷ 324. Weight in lb = volume × bulk density.

A worked example

A 6 × 6 ft sandbox filled 6 inches deep uses 0.67 yd³, or 18 ft³, before allowance.

How to Use the Sand Calculator

Measure the area at the intended finished dimensions. Enter a diameter for a circular sandbox, length and width for a rectangular bedding layer, or a surveyed area for an irregular location. Set the depth of sand you will actually place, excluding an existing layer you are keeping. Select dry sand, damp sand, play sand, or masonry sand as a weight estimate. The supplier’s as-delivered bulk density is the best input when paying by the ton. Under Order options, enter bag weight or bag volume exactly as printed. For bagged sand, compare the number of whole bags with the bags you can store and carry.

Sandbox Refill

Measure the inside space, including any tapered sides where the fill line is wider than the bottom. A 5 × 5 ft box filled 5 inches deep uses about 10.42 ft³. Put in the actual top-up depth for a refill. If two inches remain and the target is five inches, use three inches for 6.25 ft³ instead. Measure the remaining depth at several points, then rake it flat before the final check. A playground product specified as play sand may have a different package weight or density from a local bulk masonry sand. For a container with a labeled capacity, the cubic feet to cubic yards converter can translate its volume into a delivery quote.

Bedding for a Paver Walk

Measure the area that will be screeded and pull the planned bedding depth from the installation specification. A 4 × 36 ft walk with a 1-inch bedding layer uses 12 ft³, or about 0.44 yd³. Work from the compacted base elevation so the bedding depth remains reasonably uniform. Measure extra footprint at a landing or step separately and add it if the sand specification is the same. Use the paver base calculator to keep bedding and the aggregate base separate. The paver sand calculator also has a jointing mode based on product coverage, which uses the area and label coverage instead of a bedding thickness.

Leveling a Small Surface

If a manufacturer calls for sand under a product, check whether it specifies a material grade, an allowed leveling tolerance, and a different base for low or soft ground. Make several depth readings from a level reference to the supporting surface. A rectangle with a steady taper from 1 to 2 inches can use 1.5 inches as its average. Over 96 ft², that gives 12 ft³. Estimate distinct depressions separately from the uniform bedding above them. A pair of deep spots can otherwise inflate the assumed layer across the whole area. After checking the base instructions, use the calculator to compare a partial-yard order with enough bags for the actual volume.

Sand Depth and Package Coverage

The table uses dry sand at 2,700 lb/yd³, or 100 lb/ft³, making an illustrative 50 lb bag equal to 0.5 ft³. Prefer a manufacturer’s published bag yield when available. Moisture and loose packing can change the relationship between pounds and cubic feet.

Depth Area per yd³ Area per 50 lb bag at 100 lb/ft³
½ in 648 ft² 12 ft²
1 in 324 ft² 6 ft²
2 in 162 ft² 3 ft²
6 in 54 ft² 1 ft²

Ordering Sand by Bag or Scoop

Ask the yard how much its scoop holds and whether a partial scoop is available. A small bedding job can be cheaper in bags after a minimum delivery charge. For the sandbox, carrying and storage may favor smaller packages. Compare the whole-bag price with the delivered price for the volume you will actually use, and keep leftover sand dry if the next job has a specified moisture condition.

Common questions

How many tons are in a cubic yard of sand?

At 2,700 lb per cubic yard the estimate is 1.35 US short tons. A load quoted at 3,200 lb per yard comes to 1.60 short tons for the same volume. Use the density that corresponds to your delivery conditions when comparing prices per ton.

How much sand covers 100 square feet at 1 inch?

You need 8.33 ft³, which is about 0.31 yd³. At a verified yield of 0.5 ft³ per bag, buy 17 whole bags before any additional allowance. Keep the 8.33 ft³ estimate for comparing package sizes.

How many 50 lb bags of sand do I need?

Select a weight-based bag and enter 50 lb. The count uses your chosen sand density and rounds up to whole bags.

Does wet sand weigh more?

Yes. Moisture changes weight and can also change loose bulk volume. Check the delivered material density rather than treating all sand as identical.

Can I calculate a circular sandbox?

Choose Circle, enter its inside diameter and fill depth. The calculator uses π × radius² for the area.

More bulk & landscape calculators

Browse full directory ↗

Your project list

Estimates saved on this device