Paver Sand Calculator

Calculate bedding sand or polymeric jointing sand for your pavers.

Your measurements

Order options

Your estimate

Live calculation
0.62yd³

Measured quantity · no extra allowance

Order volume16.67 ft³
Estimated weight0.83 US tons
Whole bags34 0.5 ft³

Calculation & all units

200 ft² × 1 in ÷ 324 × 1 = 0.62 yd³

Order volume
16.6667 ft³
Estimated weight
0.8333 US tons
Whole bags
34 0.5 ft³
Area
200 ft²
Measured volume
0.6173 yd³
Metric volume
0.4719 m³
Metric mass
755.9873 kg
Volume-based truckloads
1 loads
Measurement planDimensions in feet
A dimension guide for your estimate
Estimate0.62 yd³View result

Calculation method

Bedding sand is a volume calculation beneath the pavers. Polymeric jointing sand is estimated using the product coverage per bag for your paver size and joint dimensions. Manufacturer coverage data accounts for differences in product and installation.

Bedding yd³ = area × depth in inches ÷ 324. Jointing bags = area × allowance factor ÷ labelled coverage per bag.

A worked example

At 1 inch deep, a 100 ft² patio needs 0.31 yd³ of bedding sand. A jointing product covering 60 ft² per bag needs 2 bags for the same area.

How to Use the Paver Sand Calculator

Choose Bedding layer for sand that supports the pavers. Measure its footprint and enter the depth called for by the installation. Choose Polymeric joints when using a bagged product to fill joints after laying the pavers. In that mode enter the coverage from the label for your paver size and joint dimensions. Use Known area for an irregular paved surface. In Order options add any extra material, or enter the price per bag or bulk unit. Switch modes before estimating the second material and save the bedding and jointing results as separate entries in your list.

Screeding a New Patio

Measure the portion where a uniform bedding layer is actually needed. At 1 inch thick, a 14 × 18 ft rectangle needs 21 ft³, or about 0.78 yd³. The edge restraint or aggregate base might extend farther than the sand. Keep those measurements separate. Before placing an order, confirm whether the installation calls for a loose screeded depth or an established finished layer and check material grading. Use the paver base calculator for the aggregate underneath, with its own thickness and density. A paving crew can then see both quantities without accidentally treating the two layers as one product.

Filling Joints in a Newly Laid Walk

Measure the finished paved area, including the wider sections where the same pavers and joint widths continue. A bag rated for 55 ft² on the installed pavers covers a 210 ft² area in four whole bags. If cut stone or wider joints reduce that rating to 38 ft² per bag, the same area needs six bags. Ask the product maker for guidance for deep joints and open textures. Enter a separate area for a section that uses another pattern. The paver calculator can work out surface piece quantities while you obtain the jointing product’s coverage chart.

Replacing Sand in Existing Joints

Check the depth of the voids after removing loose or damaged material. Choose a product compatible with the existing installation and follow its required minimum joint depth and cleaning instructions. A 90 ft² repair might need two bags if the product’s effective coverage there is 60 ft² per bag. When you are treating only a cluster of zones, outline the patches and total just that area. A full re-joint is a separate scope with a different footprint. Record the existing paver thickness and actual joint width so a bag quote made for a thin paver does not get applied to a deeper repair.

Bedding Volume and Joint Bag Examples

The values below show the two calculation modes for a 120 ft² area. Bedding uses layer thickness. The joint examples use hypothetical label coverage per bag. Copy the value from your product label rather than choosing the nearest illustrative row.

Mode Input Quantity for 120 ft²
Bedding ¾ in depth 7.5 ft³
Bedding 1 in depth 10 ft³
Bedding 1½ in depth 15 ft³
Jointing 30 ft² per bag 4 bags
Jointing 45 ft² per bag 3 bags
Jointing 60 ft² per bag 2 bags

Common questions

How many bags of bedding sand cover 100 square feet at one inch?

One inch over 100 ft² is 8.33 ft³. With a verified half-cubic-foot yield you need 17 whole bags. If the bags only list weight, use the product’s volume yield or enter the supplier’s bulk density for the corresponding grade.

How much polymeric sand for 200 square feet?

At 60 ft² per bag the answer is four bags. At 40 ft² per bag it is five. Use the rating for the specific paver size, joint width and depth. Add extra before rounding if the label or your measured conditions warrant it.

Does wider joint spacing change the estimate?

Wider joints usually need more fill for the same paver area. Use the lower coverage listed for your actual spacing. If the material has a maximum permitted joint width, follow that specification before estimating an order.

Are bedding sand and polymeric sand interchangeable?

They perform different jobs. Bedding sand supports pavers, while a compatible polymeric product fills the joints. Choose the mode that matches your purchase.

What coverage should I enter for polymeric sand?

Use the manufacturer table for your joint width, joint depth and paver size. The initial 60 ft² is an editable example.

Why round up bags?

Whole bags are purchased, so the result rounds up after the allowance has been applied.

More bulk & landscape calculators

Browse full directory ↗

Your project list

Estimates saved on this device