Gravel Calculator

Calculate gravel in cubic yards, tons and bags, with an adjustable ordering allowance.

Your measurements

Order options

Your estimate

Live calculation
2.47yd³

Measured quantity · no extra allowance

Order volume66.67 ft³
Estimated weight3.46 US tons
Whole bags134 0.5 ft³

Calculation & all units

200 ft² × 4 in ÷ 324 × 1 = 2.47 yd³

Order volume
66.6667 ft³
Estimated weight
3.4568 US tons
Whole bags
134 0.5 ft³
Area
200 ft²
Measured volume
2.4691 yd³
Metric volume
1.8878 m³
Metric mass
3,135.9472 kg
Volume-based truckloads
1 loads
Measurement planDimensions in feet
A dimension guide for your estimate
Estimate2.47 yd³View result

Calculation method

Measure the finished area and the intended depth. Gravel grades and moisture change bulk density. Confirm the weight per cubic yard with your supplier before ordering by the ton. The allowance is extra loose material above the measured volume.

Cubic yards = area in ft² × depth in inches ÷ 324. Short tons = cubic yards × density in lb/yd³ ÷ 2,000.

A worked example

A 20 × 10 ft area at 4 inches needs 2.47 yd³ before allowance. At 2,800 lb/yd³, that is 3.46 short tons.

How to Use the Gravel Calculator

Measure the usable footprint where gravel will actually sit. A rectangular lane needs its length and width. A circular turnaround needs its diameter. For an awkward outline, sketch adjoining rectangles or triangles, calculate their areas, and enter the total under Known area. Enter the depth of the particular layer you are buying. Select the grade for a starting density, then replace that figure under Order options if the quarry gives you a value. Compare cubic yards to a volume quote or short tons to a scale-based quote. If you buy bags, enter the printed bag volume or weight and use the whole-bag count.

Driveways and Turnarounds

Walk the driveway from the road to the parking area and measure it in sections where the width changes. A 10 × 50 ft run at 4 inches takes 6.17 yd³ before allowance. A 12 × 18 ft pullout at the same depth takes another 2.67 yd³. The two zones can go into one known-area estimate if the material is identical. If the pullout needs deeper fill, calculate it separately. Separate a compacted base from the wearing course because the material and depth may change between layers. Use the crushed stone calculator for a base quoted in a specific aggregate grade.

French Drain Trenches

Use the dimensions of the stone envelope shown in your drainage design. This can be smaller than the entire excavation if soil or bedding occupies part of the trench. Forty feet of trench with a stone cross section 1 foot wide and 1 foot deep holds about 1.48 yd³ before displacement. If a 4-inch outside-diameter pipe runs through that full volume, its outside envelope takes about 3.49 ft³, leaving about 1.35 yd³ for stone. Check the depth above and below the pipe, and measure branch runs separately. Ask the supplier about the washed grade specified for drainage and use the quoted density for the haul weight.

Walkways and Patios

A path with a shallow gravel finish needs less material than the foundation beneath a paved walk. For a 3 × 30 ft path at 2 inches, estimate 15 ft³ or about 0.56 yd³ before allowance. If the walk has a bend, measure the centerline length and multiply by the average width, then check widened landings separately. Use the pea gravel calculator for a rounded finish and the paver base calculator for a paved section that needs both aggregate and bedding sand. Keep the desired gravel surface below edging tops so the finished edge matches your layout.

Gravel Depth and Bag Coverage

Figures assume an even layer before extra material. Small differences can affect a whole-bag order: keep the unrounded volume when dividing by bag size. A 0.5 ft³ bag covers 3 ft² at 2 inches, so a 90 ft² path of that thickness uses 30 bags.

Finished depth Coverage per yd³ Coverage per 0.5 ft³ bag
2 in 162 ft² 3 ft²
3 in 108 ft² 2 ft²
4 in 81 ft² 1.5 ft²
6 in 54 ft² 1 ft²

Comparing a Pickup Load with Delivery

A volume that fits in a pickup bed can still exceed its payload. At the default density, half a cubic yard weighs about 1,400 lb before the driver or equipment. Check the available payload for the actual vehicle and ask the supplier what can be loaded accurately. If you price two smaller deliveries, include the fee for each visit.

Common questions

How many tons are in a cubic yard of crushed gravel?

At 2,800 lb per cubic yard the estimate is 1.40 US short tons. A heavier road base quoted at 3,000 lb per yard would be 1.50 short tons. Ask whether the truck is sold by the scale ticket or by the bucket.

How much gravel do I need for a 100 ft driveway?

With a 10 ft width and 4-inch layer, the volume is 12.35 yd³ before allowance. At 2,800 lb/yd³ that is about 17.28 short tons. The actual width, base specification and access for the delivery truck will determine the order.

How much gravel covers a 10 × 10 ft area?

At 2 inches deep, the measured volume is 0.62 yd³. At 4 inches, it is 1.23 yd³. Add your selected ordering allowance after calculating the measured volume.

Can I use this for a driveway?

Yes. Enter the finished dimensions and design depth. Use the density and extra loose-material percentage supplied for your aggregate. Depth presets are examples, and ground conditions may require a different base.

How many bags should I buy?

Divide the order volume by the volume printed on each bag and round up. You can switch to a weight-labelled bag and use the selected bulk density.

More bulk & landscape calculators

Browse full directory ↗

Your project list

Estimates saved on this device