Retaining Wall Calculator

Estimate block courses, cap stones and drainage backfill for a straight wall.

Your measurements

Order options

Your estimate

Live calculation
100blocks

Material estimate · caps and backfill priced separately

Courses5 including buried
Cap stones20 caps
Drainage backfill1.85 yd³

Calculation & all units

20 blocks/course × 5 courses × 1 walls × 1, rounded up

Courses
5 including buried
Cap stones
20 caps
Drainage backfill
1.8519 yd³
Visible face
40 ft²
Measurement planDimensions in feet
A dimension guide for your estimate
Estimate100 blocksView result

Calculation method

Count a straight, single-thickness wall using the actual face size of the blocks. Partial courses and blocks round up. Buried courses are added below the visible height. This is a material estimate; wall engineering, drainage design and reinforcement require the applicable design specifications.

Blocks = ceiling(length ÷ block length) × (ceiling(visible height ÷ block height) + buried courses), then add waste.

A worked example

A 20 ft long, 2 ft visible wall using 12 × 6 inch block faces needs 80 blocks above grade and 20 more for one buried course, before waste.

How to Use the Retaining Wall Calculator

Measure the length along the run and enter the visible block height above grade. Enter actual block face length and course height using the installed dimensions. In Order options set the number of buried courses and whether to include caps. Enter cap length and backfill width separately if the design needs them. The estimate rounds up for full blocks and courses and provides a separate cap count. For a wall with changing height, split it by course height and estimate sections independently. Use the wall system’s design and installation instructions for dimensions, embedment, site loads and drainage.

A Straight Border Wall

A 24 ft run uses 24 blocks per course with a 12-inch installed face length. An 18-inch visible height with 6-inch courses needs three above grade. If the plans call for a full buried course, the starting estimate is 96 blocks before allowance. Caps are measured separately using cap length. Confirm whether the manufacturer’s first course requires a different unit or leveling pad, since a mixed system can change the order. Mark returns and where the wall terminates at paving. Use the paver base calculator to estimate specified aggregate for a separate adjacent surface or pad.

A Stepped Wall on a Slope

Take the run length for each visible height. A 12 ft segment with 18 inches visible and a separate 8 ft segment with 30 inches visible have different course totals. With 12-inch faces and 6-inch courses, they need 36 and 40 visible blocks. If each segment has one buried course, add 12 and 8 respectively, for 96 blocks before waste. A manufacturer’s detail can call for overlapping or stepped buried courses, which may add units near the transition. Draw these steps and any corner intersections. Use the fill dirt calculator for other grade restoration that uses a separate approved material.

Estimating the Drainage Stone Envelope

Measure the stone zone indicated in the design and keep it separate from soil behind the drainage zone. A 20 ft run with a 1 ft wide zone and an actual 2.5 ft height takes 50 ft³ before subtracting any components that occupy that space. That is 1.85 yd³. If the calculator models the gravel zone with total block course height, compare the result with the height that really receives stone. Deep footing zones or narrow returns may require separate entries. Use the crushed stone calculator to obtain a separate loose order and weight for the specified washed aggregate.

Block Courses and Cap Count

This sample is for a 20 ft straight run, 12 × 6 in block faces, one buried course and 12-inch caps. Quantities exclude cuts and extra material. Match the height to the design per course, and check corners separately if they use specialty pieces.

Visible courses Visible height Blocks including buried Caps
2 12 in 60 20
3 18 in 80 20
4 24 in 100 20
5 30 in 120 20

Common questions

How many retaining wall blocks for a 20 ft wall that is 3 ft high?

With a 12-inch face and 6-inch courses, six visible courses use 120 blocks. One full buried course brings the total to 140 before allowance. Estimate caps separately unless the chosen system uses a block that serves the same purpose.

How do I estimate blocks for wall corners?

Count the intersection according to the system’s corner or return detail. A corner block can occupy part of both measured runs, so summing whole courses from two overlapping rectangles may count it twice. Check the special unit’s face dimensions and list corner pieces independently.

Can I estimate a curved wall by its straight end-to-end length?

Measure along the intended block face rather than along the chord between endpoints. A tight curve may need tapered pieces or smaller blocks, depending on the product’s minimum radius. Confirm the layout and expected block count on a scaled plan before ordering.

Does the height include the buried course?

Enter the visible wall height. The separate buried-course count adds blocks below grade.

Are caps included in the block count?

Caps are shown separately, based on the cap length you enter.

How is drainage stone calculated?

The estimate uses wall length, full constructed height and the backfill width you enter. Confirm the backfill geometry and drainage details from the wall design.

More bulk & landscape calculators

Browse full directory ↗

Your project list

Estimates saved on this device