Calculation method
Fill dirt is used to build up levels. Enter the finished volume and an added-volume allowance for settlement or compaction. Truck capacities can be limited by both volume and legal payload, so the displayed loads are volume-based estimates.
A worked example
A 20 × 10 ft fill area at 6 inches needs 3.70 yd³ finished. A 15% allowance increases the order to 4.26 yd³.
How to Use the Fill Dirt Calculator
Measure the footprint and the depth to the proposed finished grade. For a rectangular patch with a steady taper use the average of the two end depths. For an uneven lot, divide the site into measured grid sections and calculate representative depth per section. Enter the product density for a weight quote. Under Order options, review the preset extra volume. Set it to zero to see the geometric fill alone, or use a supplier-recommended loose-to-finished allowance. Enter the actual usable truck capacity when comparing deliveries and discuss any lower weight limit for the particular dirt.
Filling a Shallow Depression
Mark the area where grade needs to rise and measure from a taut level line or a planned sloping reference. A 16 × 25 ft zone averaging 4 inches of fill takes about 4.94 yd³ finished. At 15% extra loose volume the order is about 5.68 yd³. If the back half is consistently twice as deep, split it off and take more representative depth readings. Include space that must be left for a prepared cap. The topsoil calculator can estimate the separate cover layer once you know the area and thickness. The two totals can be delivered or handled independently.
Backfilling a Removed Landscape Feature
After a large planter or other landscape feature is removed, measure the actual cavity from its new bottom. A 6 × 10 ft cavity that is 18 inches deep has 90 ft³ of space. If 4 inches will become topsoil, the 14-inch dirt layer is 70 ft³ or about 2.59 yd³ finished. Mark the transition from lower fill to topsoil as work advances. Remove voids from the measurement where a footing or conduit remains. Account for the intended final use when choosing fill, because a lawn and the support beneath paving have different specifications. The paver base calculator can handle separately specified granules and bedding.
Splitting an Order Between Delivery Locations
Use distinct estimates for separate patches if handling requires more than one drop. A seller might offer the same nominal truck capacity for a lighter sandy fill and a dense damp fill, but the latter can reach a payload limit first. An order of 8 yd³ at 2,500 lb/yd³ weighs about 20,000 lb. A permitted payload of 15,000 lb would limit that product to about 6 yd³ per load even where the bed physically holds more. Get the seller’s effective cubic-yard limit, and review access and delivery sequence before committing. Save the loose volume and estimated weight for each location.
Finished Volume and Loose Allowances
These figures apply to a 200 ft² area and an illustrative 15% increase. A 15% added-volume factor represents how much extra you buy relative to the finished space. If the supplier instead reports that 15% of loose volume disappears, divide the finished figure by 0.85. Document the assumption in the order.
| Average depth | Finished fill | Loose at 15% extra |
|---|---|---|
| 3 in | 1.85 yd³ | 2.13 yd³ |
| 6 in | 3.70 yd³ | 4.26 yd³ |
| 9 in | 5.56 yd³ | 6.39 yd³ |
| 12 in | 7.41 yd³ | 8.52 yd³ |
Checking Elevations After Each Lift
If the fill is installed in multiple lifts, keep the total finished depth in the calculator and break the delivered total into placement stages afterward. Check each completed grade against the string or benchmark. Where a site needs engineered fill, use the specified material and compaction requirements for your takeoff and ask the contractor to verify the loose quantity.
Common questions
How much does a cubic yard of fill dirt weigh?
At the 2,500 lb/yd³ planning value, one loose cubic yard weighs 1.25 US short tons. Moisture, stones and the composition of the fill can make a different delivered load heavier. Ask for the yard’s measured density for a scale-based quote.
How much fill dirt for a 10 × 20 ft area that is one foot deep?
That space takes 200 ft³ or 7.41 yd³ before allowance. A 15% addition gives about 8.52 yd³. At 2,500 lb/yd³, the loose order is approximately 10.65 short tons. Subtract any volume that will be filled by a separate finish material.
Does the estimate include compaction?
The result applies the percentage you enter as extra volume. Enter the figure specified for your fill material and placement method.
Can fill dirt replace garden soil?
Fill material and planting soil serve different purposes. Use the Soil calculator when estimating a growing medium.
How many dump trucks are needed?
Set the actual truck capacity in Order options. The count is rounded up from order volume and should be checked against the truck weight limit.